How to change engine oil and filter on Mitsubishi L200 KA – replacement guide
MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D (KA4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D (KA4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D 4WD (KB4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D 4WD (KB4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D (KA4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D (KA4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D 4WD (KB4T), MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D 16V 4WD, MITSUBISHI L 200 / Triton Pickup (KA_T, KB_T) 2.5 DI-D 4WD (KB4T) … View more
The steps may slightly vary depending on the car design.
How to change the oil filter and engine oil on the MITSUBISHI L200 KA [AUTODOC TUTORIAL]
Oil filter
- Replace the oil filter every time you change the engine oil.
- Before getting down to work, warm up the engine to reduce the viscosity of the oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – Mitsubishi L200 KA – should be done with the engine switched off.
- Step 1
Open the bonnet.
- Step 2
Use a fender protection cover to avoid damaging the paintwork and plastic parts of the car.
- Step 3
Unscrew the oil filler cap.
- Step 4
Pull up the oil dipstick.
- Step 5
Lift the vehicle using a vehicle lift or place it over an inspection pit.
Replacement: engine oil and filter – Mitsubishi L200 KA. Tip from AUTODOC experts:The vehicle must be level, but if it is at an angle, the drain plug must be at the lowest point.
- Step 6
Put an oil drain pan with a capacity of at least 8 litres under the drain hole.
- Step 7
Clean the area of the oil pan drain hole. Use a wire brush. Use an all-purpose cleaning spray.
- Step 8
Unscrew the drain plug. Use a 17 mm socket. Use a ratchet wrench.
- Step 9
Drain the used oil.
Caution!The oil may be hot.Wait until the oil has completely flowed out of the drain hole.
- Step 10
Turn the wheels fully to the right.
- Step 11
Unscrew the oil filter. Use a 100-15F cup type oil filter wrench. Use a ratchet wrench.
- Step 12
Remove the oil filter.
- Step 13
Clean the oil filter mounting seat. Use an all-purpose cleaning spray.
- Step 14
Apply a small amount of fresh oil to the new filter's gasket.
Step 15
Install the new oil filter.
- Step 16
Tighten the oil filter. Use a 100-15F cup type oil filter wrench. Use a torque wrench. Tightening torque: 22 N·m.
- Step 17
Clean the area of the oil pan drain hole. Use an all-purpose cleaning spray.
Find out which tyre and wheel sizes are compatible with the MITSUBISHI L200 / Triton IV Pickup (KA, KB) model
Popular maintenance tutorials for MITSUBISHI L 200 (KB_T, KA_T)
Free download PDF 1.08 MB
Free download PDF 1.9 MB
Free download PDF 1.11 MB
Free download PDF 1.43 MB
Free download PDF 563.2 KB
Free download PDF 1.2 MB
Complete guides for changing the Oil filters on different MITSUBISHI L200 models
Free download PDF 2.82 MB
Free download PDF 2.34 MB
Free download PDF 1.84 MB
Track expenses, manage logs, schedule replacements, and more.
How to unlock your car without a key | AUTODOC tips
Checking the starter without removing it | AUTODOC tips
5 signs of a faulty strut mount and how to fix it
How I started restoring a driveshaft | Drivetrain restoration – Part 1
Most commonly replaced car parts on MITSUBISHI L200
Professional manuals for the most common MITSUBISHI models
